添加叔丁醇钾对Mg(NH2)2-2LiH体系储氢性能的影响

叔丁醇钾(C_4H_9OK)的添加显著改善了Mg(NH_2)_2-2LiH体系的储氢性能。添加0.08 mol C_4H_9OK的Mg(NH_2)_2-2LiH-0.08C_4H_9OK样品表现出最佳储氢性能。该样品的起始放氢温度仅为70℃,较Mg(NH_2)_2-2LiH原始样品降低了60℃;130℃完全放氢后,该样品可在50℃开始吸氢,较原始样品降低了50℃。Mg(NH_2)_2-2LiH-0.08C_4H_9OK样品可在150℃的等温条件下50min内迅速放出质量分数3.82%的氢气,完全放氢后可在120℃的等温条件下50 min内快速吸收质量分数4.11%的氢气,表现出良好的吸放氢动力学性能。C_4H_9OK的添加降低了样品放氢反应的表观活化能和反应焓变,改善了放氢反应的动力学和热力学性能,从而降低了放氢反应温度。进一步的放氢反应机理研究发现,在180℃之前,C_4H_9OK对Mg(NH_2)_2-2LiH体系的放氢起催化改性作用;温度继续升高后,C_4H_9OK将会分解并参与放氢反应最终生成Li_3K(NH_2)_4。     

基于原位配体反应的锰(Ⅱ)配位聚合物的合成、结构和催化性质

采用水热方法,选用含2个氰基的醚氧桥联羧酸配体(Hdbna)和2,2′-联吡啶(2,2′-bipy)与MnCl2·4H2O反应,合成了一个二维配位聚合物[Mn(μ3-Hdpna)(2,2′-bipy)]n (1),并对其结构和催化性质进行了研究。在配合物1中,配体Hdbna在水热反应条件下,通过原位反应被转化成醚氧桥联三羧酸配体(H3dpna)。结构分析结果表明配合物1的晶体属于三斜晶系,P■空间群。配合物1具有二维层结构。研究表明,配合物1在硅腈化反应中表现出较高的催化活性。     

钙钛矿组分和结构设计及其发光二极管器件性能研究进展

有机-无机杂化钙钛矿发光二极管(LED)的性能在短短几年时间内飞速提升, 近红外光器件的效率已达21.6%, 绿光器件效率也达到20.3%, 达到可以和商业化的有机发光二极管媲美的水平; 即使是稍有逊色的稳定性方面也有很大进展, 报道的最长器件半衰期已达到250 h. 器件性能的飞速提升得益于钙钛矿本身优异的光电性质, 而且通过丰富的化学手段可进一步对钙钛矿材料的组分和结构进行调控, 从而优化器件性能. 本综述从组分设计、缺陷钝化和界面修饰的角度出发, 重点分析了组分和结构设计对钙钛矿LED器件效率和稳定性的影响, 最后对钙钛矿发光二极管的未来发展进行展望.     

Synthetic studies towards(-)-deserpidine:Total synthesis of the stereoisomer and derivative of (-)-deserpidine

The asymmetric synthesis of 16,17,20-epi-deserpidine and a derivative of(-)-deserpidine has been achieved.Key feature s in the assembly of the pentacyclic framework include a visible-light photocatalytic intra-/inter-/intramolecular radical cascade reaction to construct the tetracyclic ABCD ring system in one-pot and an intramolecularaldol reaction to forge the cyclohexane E ring.     

Robust nickel silicate catalysts with high Ni loading for CO2 methanation

CO₂ is the main component of greenhouse gases and also an important carbon source. The hydrogenation of CO₂ to methane using Ni-based catalysts can not only alleviate CO₂ emissions but also obtain useful fuels. However, Ni-based catalysts face one major problem of the sintering of Ni nanoparticles in the process of CO₂ methanation. Thus, this work has synthesized a series of efficient and robust nickel silicate catalysts (NiPS−X) with different nickel content derived from nickel phyllosilicate by the hydrothermal method. It was found that the Ni loading plays a critical role in the structure and catalytic performance of the NiPS−X catalysts. The catalytic performance gradually increases with the increase of Ni loading. In particular, the highly dispersed NiPS-1.6 catalyst with a high Ni loading of 34.3 wt% could obtain the CO₂ conversion greater than 80%, and the methane selectivity was close to 100% for 48 h at 330 °C and the GHSV of 40,000 mL g⁻¹ h⁻¹. The excellent catalytic property can be assigned to the high dispersion of Ni nanoparticles and the strong interaction between the active component and the carrier, which is derived from a unique layered silicate structure with lots of nickel phyllosilicate and a large number of Lewis acid sites.     

减压蒸馏生物油与乙醇在ZSM-5/MCM-41上共催化裂化

采用减压蒸馏生物油为原料,与无水乙醇2:3(质量比)混合,在固定床中ZSM-5/MCM-41分子筛上共催化裂化,考查了反应温度和质量空速(WHSV)对裂化产物的影响。对ZSM-5/MCM-41进行了NH₃-TPD、BET、N₂吸附-脱附等表征,对裂化气体产物通过气相色谱仪分析,减压蒸馏生物油和精制生物油采用气相色谱-质谱联用仪进行定量分析。结果表明,反应温度500 ℃、WHSV 3.75 h^-1为反应优化工况。此反应条件下,精制生物油酸类物质从减压蒸馏生物油中的25.6%降至反应后的0.1%,效果显著,且精制生物油产率为46.8%,气体产物中CO₂和CO的浓度共9.5%。     

Electrochemical characterization of MnO2 as electrocatalytic energy material for fuel cell electrode

 Development of inexpensive non Pt based high electrocatalytic energy materials is the need of the hour for fuel cell electrode to produce clean alternative green energy from synthesized bio alcohol using biomass. MnO₂, electro synthesized at different current density is found to be well performed electrocatalytic material, comparable to Pt, with higher current density, very low overvoltage for the electrochemical oxidation of methanol. From EIS study, the polarization resistance of the coated MnO₂ is found to be much low and electrical double layer capacitance is high, the effect increases with increase in current density of electro deposition. XRD, EDX and AAS analysis confirm the MnO₂ deposition. The morphology of SEM images exhibits an enhanced 3D effective substrate area, for electro oxidation of the fuel. A few nano structured grains of the deposited MnO₂ is also observed at higher current density. The fact supports that a high energetic inexpensive electro catalytic material has been found for fuel cell electrode to synthesis renewable energy from methanol fuel.     

SCR脱硝过程中SO2催化氧化的原位红外研究

采用工业用V₂O₅-WO₃/TiO₂催化剂,基于傅里叶原位红外光谱(FT-IR)技术考察SO₂的氧化过程及烟气组分对SO₂氧化行为的影响;结果表明,SO₂在催化剂表面氧化主要是首先吸附在催化剂表面V₂O₅活性位上,占据其O原子,以SO^2-₃形式存在,后与催化剂表面V⁵⁺-OH发生反应,生成金属硫酸盐(VOSO₄)中间产物,O₂重新氧化催化氧化过程中由于被SO₂夺取O原子而被还原的V₂O₅物种,使V⁴⁺转化为V⁵⁺,促进金属硫酸盐(VOSO₄)向SO₃转化;SO₂与NO、NH₃的竞争吸附阻碍SO₂在V₂O₅活性点位上的氧化;在SCR中,NO的脱除与SO₂的氧化是相互抑制的关系。     

预裂化理论研究:基质表面酸性位类型及不同类型酸性位接触顺序对裂化过程小分子烯烃收率的影响

在区分氢负离子转移反应与氢转移反应、非选择性氢转移反应与总的氢转移反应的情况下,通过合成物性相近但酸性不同的氧化铝,用以作为裂化催化剂基质材料,在固定床反应器上考察了催化裂化过程,基质酸性位类型及基质表面Lewis及Brönsted酸性位接触顺序对小分子烯烃(丙烯、丁烯)收率的影响。结果表明,催化裂化生成小分子烯烃过程中,分子筛与基质所呈现出的反应特点存在较大的区别,前者活性虽高,但总的氢转移反应活性过强。基质材料裂化活性虽低但其表面以氢负离子转移反应为主,反应路径角度更有利于小分子烯烃收率的提高。另外,基质表面存在Brönsted酸性位,或原料油首先与基质表面Lewis酸性位相接触再与Brönsted酸性位反应的预裂化过程,会在促进裂化反应发生的同时抑制总的氢转移反应,更有利于小分子烯烃收率的提高。     

不同WO3含量对CeO2-ZrO2-WO3催化剂在NH3选择性催化还原NO中的影响

采用水热法制备了CeO₂-ZrO₂-WO₃(CZW)催化剂,考察了WO₃含量对CZW催化剂上NH₃选择性催化还原NO_x性能的影响,并利用X射线衍射、N₂吸附-脱附、H₂程序升温还原、NH₃和NO程序升温脱附等方法对其进行了表征。结果表明,WO₃以无定形的形式存在于催化剂中,添加WO₃后显著提高了催化剂的表面酸性,并且在CZW催化剂上出现了强吸附的NO物种,从而有利于提高催化剂的活性。另外,适量的WO₃引入将增大催化剂的比表面积,促进催化剂的氧化还原性能,这将有利于提高SCR的催化活性。和CeO₂-ZrO₂催化剂相比,当WO₃的含量为20%时,CZW催化剂表现出良好的抗硫性能。此外,当空速为60 000 h^-1时,在200~463 ℃,该催化剂显示出了大于90% NO_x转化率。